Buy Eurotherm PID Temperature Controller, 48 x 48 (1/16 DIN)mm, 2 Output Relay, 85 → V ac Supply Voltage /CC/VH/ENG/F Browse our latest. Find great deals for Eurotherm I Temperature Controller With Mounting Bracket. Shop with confidence on eBay!. The i/i are compact high performance 4 digit units for measurement Model i: 48W x 48H x D mm. Display: .. Modbus®, Eurotherm ASCII.

Author: Nisho Jugul
Country: Iceland
Language: English (Spanish)
Genre: Music
Published (Last): 3 June 2015
Pages: 425
PDF File Size: 15.67 Mb
ePub File Size: 7.79 Mb
ISBN: 206-6-44326-918-2
Downloads: 74465
Price: Free* [*Free Regsitration Required]
Uploader: Vogrel

Only use copper conductors for connections, except thermocouple.

Eurotherm 2116I Temperature Controller With Mounting Bracket

You may also apply a 2-point calibration as follows: This is normally alarm 1. O0 to reach the Access List Heading. The tables below list all of the possible messages and their meaning. Keep pressing to increase the value.

A universal input enables 2116i of nine internally stored thermocouple types and the PT resistance thermometer. Linear inputs can be scaled to the desired display range. There are three alarm setpoints.

The indicator is supplied configured according to the ordering code given on page 5. Contact your nearest Eurotherm Controls agent for repair.

Eurotherm 2116 Temperature Controller

OP1 will flash when an alarm attached to furotherm logic output becomes true. Do not use water or water based products to clean labels or they will become illegible.

This indicator satisfies the general requirements of the industrial environment defined in EN and EN The logic can be configured as an alarm output or as an alarm acknowledge input. J Alarm 3 is active and it is a Low alarm. If, at any time, no key is pressed within 45 seconds, the display will always return to the HOME display. Peel off the protective cover from the display Unplugging the indicator The indicator can be unplugged from its sleeve by easing the latching ears outwards and pulling it forward out of the sleeve.


Voltage transients on the eurotberm supply must not exceed 2. To avoid this, before handling the unplugged indicator discharge yourself to ground.

Universal input selection Two configurable outputs Three internal alarm setpoints Heater failure detection Tactile buttons Customized operator interface. Pressing and again will show two decimal points in those alarms that. Return for repair Surotherm failure.

The operator interface can be customized to present only those parameters that an operator needs to see and adjust. Alarm Ack input Logic only D Functions: Refer to the accompanying documents Personnel Electrically conductive pollution for example carbon dust must be excluded from the cabinet in which the indicator is mounted.

Digital output Function O!

Obsolete Instruments

Take particular care not to connect AC supplies to the low voltage sensor input or logic outputs. The display units Display Units 0. In some installations the temperature sensor may surotherm live. Press and 65 Instrument list Options to select a parameter to change the setting. Press and release quickly the will be flashed for 0. The factory default is 1. Repeat for all the parameters you wish to hide or make readonly then return to operator level: Return for repair Low display range exceeded: A mild soap solution may be used to clean other exterior eurothedm of the product.


Installation must be carried out by qualified personnel. The filter requirements will depend on the type of load. Routing of wires To minimise the pick-up of electrical noise, the sensor input wiring should be routed away euroherm high-current power cables.

Voltage rating Cleaning The maximum continuous voltage applied between any connection and ground must not exceed Vac.

Eurotherm i Operating instructions |

You are now in Edit level. All isolated inputs and outputs have reinforced insulation eurothemr protect against electric shock. The parameter in the N0 list applies a fixed offset over the whole display range. Gives access to configuration level. Power Isolation The installation must include a power isolating switch or circuit breaker that disconnects all current carrying conductors. It’s a community-based project which helps to repair anything.

The first list is the alarm setpoints. O6 Continued in next column